On 8/29/2013 10:15 AM, Hans Hagen wrote:

On 8/29/2013 4:06 AM, Aditya Mahajan wrote:

...

Hi,

I am trying to pick up on an old thread of creating an overview page [1]. Basically, the idea is to create an overvew slide at the end of a presentation that shows the first page of different sections in a presentation. Based on Wolfgang's answer in that old thread, I save the relevant pages in a box, and then display them again at the end of the presentation.

This works, except that I get a series of warnings:

l.86 \placeoverviewpage LuaTeX warning (ext4): destination with the same identifier (name{aut:10}) has been already used, duplicate ignored

How do I get rid of these?

Tricky. The problem is that you flush a box (copy) so the message comes from deep inside the backend (for good reason) and so we cannot intercept it as "hey user, you use the same dest twice" simply because it's a copy and not re-rendered.

There are two solutions:

(1) strip the box before copying (i can make a helper for that - later as i have to go now): destinations, references, writes-to-lists etc

(2) you copy the old file before processing and use that one

\def\placeoverviewpage {\startstandardmakeup[\c!align=\v!middle] \getfiguredimensions[temp.pdf]%

\dorecurse{\noffigurepages}{\externalfigure[temp.pdf][\c!page=##1,\c!width=\overviewwidth]\relax\space}

\stopstandardmakeup}

...

I am afraid that I cannot create a small example illustrating this warning, so I am attaching the complete test file.

[1]: http://thread.gmane.org/gmane.comp.tex.context/72556/focus=72571

[2] It has always been a wish of mine to have it as option in the engine (pdfetex) but in luatex it's not that hard to do it myself now (i already have a stripper so I can extend that one a bit).

attached ... you can run the module for an example (you need a new beta) ----------------------------------------------------------------- Hans Hagen | PRAGMA ADE Ridderstraat 27 | 8061 GH Hasselt | The Netherlands tel: 038 477 53 69 | voip: 087 875 68 74 | www.pragma-ade.com | www.pragma-pod.nl -----------------------------------------------------------------

On 8/31/2013 5:36 PM, Aditya Mahajan wrote:

On Thu, 29 Aug 2013, Hans Hagen wrote:

...

On 8/29/2013 10:15 AM, Hans Hagen wrote:

...

On 8/29/2013 4:06 AM, Aditya Mahajan wrote:

...

Hi,

I am trying to pick up on an old thread of creating an overview page [1]. Basically, the idea is to create an overvew slide at the end of a presentation that shows the first page of different sections in a presentation. Based on Wolfgang's answer in that old thread, I save the relevant pages in a box, and then display them again at the end of the presentation.

This works, except that I get a series of warnings:

l.86 \placeoverviewpage LuaTeX warning (ext4): destination with the same identifier (name{aut:10}) has been already used, duplicate ignored

How do I get rid of these?

Tricky. The problem is that you flush a box (copy) so the message comes from deep inside the backend (for good reason) and so we cannot intercept it as "hey user, you use the same dest twice" simply because it's a copy and not re-rendered.

There are two solutions:

(1) strip the box before copying (i can make a helper for that - later as i have to go now): destinations, references, writes-to-lists etc

(2) you copy the old file before processing and use that one

\def\placeoverviewpage {\startstandardmakeup[\c!align=\v!middle] \getfiguredimensions[temp.pdf]%

\dorecurse{\noffigurepages}{\externalfigure[temp.pdf][\c!page=##1,\c!width=\overviewwidth]\relax\space}

\stopstandardmakeup}

...

I am afraid that I cannot create a small example illustrating this warning, so I am attaching the complete test file.

[1]: http://thread.gmane.org/gmane.comp.tex.context/72556/focus=72571

[2] It has always been a wish of mine to have it as option in the engine (pdfetex) but in luatex it's not that hard to do it myself now (i already have a stripper so I can extend that one a bit).

attached ... you can run the module for an example (you need a new beta)

Thanks, works nicely.

I'll add the configuration commands, and release it as a module.

ok; i already did the commandhandler so it should be easy to extend .. no problem adding it to the standard distribution (i'll add some comments then about the 'issue' of duplication) as it can probably serve some more purposes (and be extended) Hans -- ----------------------------------------------------------------- Hans Hagen | PRAGMA ADE Ridderstraat 27 | 8061 GH Hasselt | The Netherlands tel: 038 477 53 69 | voip: 087 875 68 74 | www.pragma-ade.com | www.pragma-pod.nl -----------------------------------------------------------------